Sunday, April 13, 2014

Part Two of my toy box build.

I'm going to spend a little more time on the toy box today. I need to get it completed as soon as possible. I have to deliver it next weekend.

This is the bottom of the box. It needs a round-over detail routed on the front and both sided.I am using my router table but a hand held router will do fine for this job.  
This picture shows a small round-over I routed on three sides. 
While I had the router table set up I worked on the lid also. I did the same three sides but on the lid I did the top and bottomto give it a bull nose effect.
I set the box on the bottom. Make sure it is lined up with equal space all around. 
Use a square in one corner to make sure the box is squared up. If you screw it down out of square the lid will bind. Start with one screw then make sure it's still square. As you install more screws keep checking it.   
Here is the box with the bottom installed . Notice the over lap of the bottom. Notice that the front paned is set back from the sides by 1/2". I'm going to install the child's name on the front using 1/2" thick MDF. The recessed front panel will Let the letters sit back a little. 
The next step is to plug the pocket holes. Kreg sells these plugs along with the screws. Put a little glue in the hole and install the plug. 
Install a plug in every hole. Let the glue dry for a while before you start sanding them flush. 
A sander and some elbow grease is needed to get the plugs flush. The better you get the sanding done here the better the paint job will look.  
I'm going to finish up this session by easing over all the sharp edges and do some prep sanding. MDF has very porous edges. If you don't prep it right you will have trouble getting paint to cover the edges. I'm going to sand the edges as silky smooth as possible going through the grits. I'll sand down to at least 220 grit. In the next session I'll make a solution to apply to the edges to seal them. This sealer will keep the paint from soaking in so bad. I'm going to take a break and do some more work tonight. 




The Scrollsaw Workshop is primarily supported by donations. If you enjoy this Blog and would like to make a donation please click this link. Your support is greatly appreciated. Make A Donation


If you would like to have all the patterns in the Scrollsaw Workshop catalog you can buy the first six years DVD and the 2013 update DVD at this link. DVD #1 is $20 and contains over 1,100 patterns. The 2013 update DVD is $7.50 and has another 178 patterns.

Part One of my toy box build. Long Post with lots of pictures.

My wife informed me it was time to build another toy box. Our great-niece Aubrey is about to turn one. Over the years I have built either a rocking horse or toy box for the kids as they turn one. I always try to use the scroll saw to customize the toy boxes with ornaments and names.

I thought some of you might interested to see my progress as I go along. This is my day one progress. I pretty much have the box pieces cut. If I don't get called in to work tomorrow I'll start with the detail work. When I have everything finished I'll publish all the dimensions for the box. I'll also make a few different ornamentation so you can make your own custom toy box.

I visited my local Home Depot and picked up five sheets of 2' X 4' X 3/4" MDF. I plan to paint the final project so MDF is a good choice over plywood. MDF is very heavy but it paints well and it's pretty easy to work with. I'll be using pocket hole joinery for construction.
From my drawing I start cutting down the MDF to size. Remember, MDF is not good on the lungs so make sure you use your dust mask and have your shop well ventilated before you start.
Here are the outside walls of the box cut to rough size. I'll cut the lid and bottom later once the box is assembled. It's easier to cut those pieces to size by measuring than to cut them from the drawings. You can adjust the size if needed that way.
My drawings have the template for the curves of the side and back walls. My plans are printed on 8.5 X 11 paper so I'll have to cut and assemble the template. The picture is for one of the side walls.
In this picture I have the template taped together and ready to apply to the side wall.
I carefully tape the template to one of the cut side walls. Just put the tape on the bottom of the template so you can lift the top in insert the carbon paper. Double check that you are putting the template on the top of the side wall.
You can use carbon paper to trace the template lines but I just use a sheet of paper with pencil. It works fine. 
Carefully trace the template curves on to the side wall. You can lift the template and make sure you have a good tracing before you remove the tape. You don't have to be perfect here. You are going to have to sand the final curve anyway to get it smooth.
Once you have a good tracing you can remove the template. If you need to, go over the tracing again to get a line you can see easily.
I'm going to use a jig saw to do a rough cut of the curves. Stay just outside the template line. We will sand the curves to their final finish. Make sure you clamp the piece to your workbench. You want to make as smooth of a cut as you can so you don't have more sanding than necessary. By the way, I'm using my new 20v cordless DeWalt jig saw. I now have the drill, circular saw and jig saw. These tools have power to spare. I'm really impressed with these products. 
I finished the rough cut with the jig saw. Now it's over the the spindle sander.
A spindle sander is the right tool for this job. If you don't have one then just sand by hand until you get a nice smooth curve. Take you time here and get it right.
Even with the spindle sander I still finish off the sanding by hand. 
Now we can use the finished side to trace the pattern on to the other side.
Make sure the sides are lined up well then just trace the curves.
Just follow the same procedure to cut this side with your jig saw.
I placed both sides in my workbench vice and made sure they matched. If not more sanding is required.
Here is a dry assembly of the progress so far. The next step is to put the curve on the back wall.
The technique for the back wall template is the same as done with the sides. I just cut the pieces and taped them together.
Carefully apply the template. You want to make sure that each end of the curve is lined up with where the side wall meets the curve. You don't want the side wall higher than the back curve.  
Back to the jig saw. Follow the same procedure as the side wall. Cut just outside the line. Sand to the line. Get this curve as smooth as possible. It's a long curve and defects will show.  
I like to do several dry assemblies as I go along. It's better to spot errors now than after everything is screwed together. Next I'll cut the finger hole on the front.
Measure over four inches from each end and make a mark. Measure down 1.5 inches at each end and make a mark. Connects these lines with a curve. I used a candle jar I had available to mark the curve.
MDF dust if fine and will make a terrible mess of your shop. As I make the cuts with the jig saw I keep my shop vac running to grab as much dust as possible. Remember that dust mask. This stuff is really not good for you. Just like the other pieces use your spindle sander and sand paper to get the front finger hole smooth.
I do another dry assembly. Looking good so far. Fingers crossed.
Pocket hole joinery is my favorite for this type of project. It's easy, It's strong and it's fast. It's so strong that I won't even use glue. MDF does not take glue on it's edges very well so I'll just depend on the pocket screws to keep things together.  
Mark the position of your pocket holes before you start to drill. It's too easy to make a mistake and place a hole on the wrong side. You don't want to have to cut another piece at this point. Just take the time to lay out the holes and save yourself the headache. 
I cut three pocket holes on each end of the front and back panels. Make sure the top pocket hole is lower than where the lid will fit. To attache the bottom I cut two pocket holes in the side wall and three in the front and back. Some people like to use more but in my experience they are so strong why cause your self more work than needed. I plan to fill the holes and sand them flush so I will keep them to a minimum. 
When you start drilling the screws into the panels they have a tendency to move. The Kreg pocket hole system has several different types of clamps. When possible use these clamps to keep things nice and flush. All I'm assembling right now are the walls. This will give me the measurements for the lid and bottom panel.
I measured and cut the bottom panel to give me a 1/2" overlap around the bottom of the box. I'll use my router to put a round-over later. I also measured and cut the lid. I cut the lid just short of the front length to make sure it does not bind when opened. I also cut the lid so it overhangs the front panel by about 1/4".

That's enough for this day. I spent about four hours to get to this point. I have some decisions to make before I start again tomorrow. Hinges, casters, paint color and more need to be worked out. If I don't get called in to work tomorrow I'll see what progress I can make. The final plans for this toy box might take a few days after I get it completed. I want to make sure I have everything where I want it before I do the final design work. I tend to make changes as I go on work like this.



Home Depot Hobby Wood Special.

 Probably the most often asked question I get is about where to buy scroll saw ready wood. Many of my patterns as well as others require thin stock. It's easy to find 3/4" thick wood but thin stock is more challenging.

The best and most economical solution is to buy lumber in the rough and dimension it to what you need. Unfortunately if you don't have a complete woodworking shop that's just not possible.

Today I was at my local Home Depot store buying supplies for a toy box I'm building and I ran across this display. This might just be a special that my local store is running but I wanted to pass it along so you can check your store. They have a big box of 1/2" thick Poplar and Red Oak. The boards are 1/2" X 5-1/2" X 24" for $1.98 and $2.88 each. I am not a big fan of either species but both are okay for many projects. 

I passed on the poplar but I did buy five of the Red Oak boards. I usually buy most of my lumber in the rough but at this price I can save all the labor of re-sawing and planning.

Most Home Depot stores carry a small selection of what they call "hobby boards". They have 1/4", 1/2" and 3/4" thick boards but they are pretty expensive. If you have no other sources it's not too bad since most scroll saw projects don't require too much wood anyway. This sale make it much easier to swallow buying project ready boards. Check out your store. I would be interested to hear if anyone else runs into this deal.


The Scrollsaw Workshop is primarily supported by donations. If you enjoy this Blog and would like to make a donation please click this link. Your support is greatly appreciated. Make A Donation


If you would like to have all the patterns in the Scrollsaw Workshop catalog you can buy the first six years DVD and the 2013 update DVD at this link. DVD #1 is $20 and contains over 1,100 patterns. The 2013 update DVD is $7.50 and has another 178 patterns.

This is the end of the daily posts. Keep scrolling for lot's more scrolls saw fun!






https://www.bearwood.com/
Bear Woods has been around since 1987 serving our hobby. They offer a wide range of craft products including Pegas scroll saw blades, clock inserts, toy parts, workshop supplies and much more. In my ten years of writing the Scrollsaw Workshop blog I have never received a complaint about Bear Woods. I get thousands of email a month so that's saying something about their customer service and quality products. Please support the people who support our hobby. Click now and visit Bear Woods.

Heritage Wood Specialties. Scroll saw ready boards!


Heritage Wood Specialties is a nationally recognized supplier of superior quality hardwoods to fine woodworkers across the US and Canada. Novice hobbyists and experienced enthusiasts alike can enjoy the high quality woodworking materials and kits available from Heritage Wood Specialties. Great source for scroll saw ready boards.

Seyco

http://seyco.com/
Seyco began business in 1986 with the goal to supply the best customer support and quality products in the scroll saw industry. I have worked with Seyco on many occasions and I can tell you they are simply the best. Please do yourself a favor and click the image above. Steve Good

Free Pattern Catalog. 1000's of free patterns.

http://www.stevedgood.com/catalog/

Thousands of FREE scroll saw patterns. No registration or signup required.

The projects form these patterns can be sold without restrictions. The patterns cannot be sold.

Click here for the Free Online Catalog.

-

Wooden Vases on the Scroll Saw Book $12 Each

http://www.stevedgood.com/woodenvases.html
Each digital book is available for download immediately after payment.
The books are $12 per edition and contains eight unique patterns each.
Watch the following video to see how easy these beautiful scroll saw vases
are to make. 

Order the $3 pdf Catalog

This is a PDF of all the patterns in my free catalog. It is for Windows only and has a program to automatically download the pattern to your computer. Please watch the video below before you order. Click the picture to order.
http://www.stevedgood.com/swpd/swpdorderpage.html
You do not need a PayPal account to order. At the bottom of the PayPal page is a button that will allow you to pay with a credit card. After successful payment click the Return to Merchant button for the download.

Stencil Printer 1.7

Stencil Printer Instruction Video.

The Scrollsaw Workshop Stencil Printer 1.7 is my latest software for creating patterns. It will create key chain fobs, desk name plates and more. Click the image above to download the latest version. It is free to use donationware. This software is for Windows PC only.

Scroll Saw Pattern Printer update 1.1

Scroll Saw Pattern Printer update 1.1
Download the Free Scroll Saw Pattern Printer Version 1.1. Create name patterns in seconds. Windows PC only.
Download Version 1.1
Please consider a $5 donation for The Scroll Saw Pattern Printer v1.1.

Scroll Saw Keychain Pattern Maker

Use the Scroll Saw Keychain Maker to start a small keychain business. Build yourself a nice display and make up severl keychains with common names. Sell at craft shows, on Ebay or at work. Everyone needs a keychain. Take custom orders. Heck just make them and give them away as gifts. It's all made easy with the Scroll Saw Keychain Maker. Watch the video demonstration then download the file below and get started with the fun.
The following link will start the download process. After the file download is complete just click the setup file and the program will be installed. Please consider a $5 donation for the program.

Download the Oval Keychain Pattern Maker.

Enjoy designing and printing these great personalized key chains. Give them as gifts, make them for fun or sell them at craft shows. It's easy, just watch the video demo then download and install the program. You will be designing these fun projects in minutes. Windows PC only.
Download the Free Oval Key Chain Pattern Maker. Create Oval key chain patterns in seconds.
Download Version .9a
Please consider a $5 donation for The Oval Key Chain Pattern Maker.

T-Shirts and More.

T-Shirts and More.
Show your love for the hobby and support the Scrollsaw Workshop. Safe and secure order fullfilled by CafePress. Take a look. You are sure to find something you like. CLICK THE IMAGE to visit the store.

The Lifter

Papa's Custom Patterns.

www.papasworkshop.net

Philip Lowndes Noah's Arc Pattern Available. Watch the video below.

This video is from Philip Lowndes. He is the designer of this beautiful Noah's Arc puzzle pattern. If you would like the pattern follow the link below.
Buy This Wonderful Heirloom Puzzle Pattern

Think Safety

Remember to keep the safety of yourself and others in your work shop in your thoughts at all times. Always wear eye and ear protection. Follow all the manufactures warnings that came with your power tools. If I demonstrate something on this web site that you don't feel is safe, don't do it. Your safety is your responsibility. Fingers are handy things, try to keep all of them.
__________________________
Disclaimer:
The Scrollsaw Workshop Blog is in no way affiliated with or sponsored by Scroll Saw Woodworking and Crafts Magazine formerly (Scroll Saw Workshop Magazine) or it's publisher Fox Chapel Publishing.

Scroll Saw Woodworking and Crafts